SBE jamming

[kpiller]

I have a SBE and am having unbelievable trouble with it not ejecting spent round and cycling new round. Jams EVERY shot!

Replace the recoil spring (the one in the stock) no good.

I am at my wits end.

Anyone help?

[M1014]

hello, I think interms of resistance,oil,burs,worn out or mismatch parts,ammo,sand,etc ,then can I fix it or do I take it to a qualified gun smith? [img]smile.gif[/img] M1014 PS pass on your findings.

[CKuwitzky]

Are you using a 3 dram load? My SBE jams as well w/ "light" target loads...less than 3 drams but functions fine w/ heavy loads...3 drams plus. The manual recommends using a heavy loads for the first 100 rounds. I have put over 500 rounds through my SBE and it still will jam about every 3rd round w/ light loads. Try a heavy load...if that doesn't work take it to a gunsmith ASAP. Good luck!

[kpiller]

I use 3 dram loads from Federal. There are 3 other guys on the team that also shoot SBE without any problem, any other ideas? I have had the gun for about 3 years, worn out part?

Originally posted by CKuwitzky:
Are you using a 3 dram load? My SBE jams as well w/ "light" target loads...less than 3 drams but functions fine w/ heavy loads...3 drams plus. The manual recommends using a heavy loads for the first 100 rounds. I have put over 500 rounds through my SBE and it still will jam about every 3rd round w/ light loads. Try a heavy load...if that doesn't work take it to a gunsmith ASAP. Good luck!

[DJ]

Check the locking head pin for wear. Mine was having trouble cycling every once in awhile, nothing like yours though. I replaced it and my problems went away.

[kpiller]

Thanks. That sounds logical to me. Have you ever heard of rotating that pin everytime you clean it? To avoid it "flat spotting"? The guy at Galyans offered that advice. His first thought though was me soft shouldering it. NAH!

I will give it a "shot" and post the results.

Originally posted by DJ:
Check the locking head pin for wear. Mine was having trouble cycling every once in awhile, nothing like yours though. I replaced it and my problems went away.

[kpiller]

Well, the verdict is mostly in on my jamming SBE. Replaced the locking pin, shot a 3DRAM load, still jammed, put a 3 3/4 DRAM in, cycled fine.

Apparently, my SBE WILL NOT shoot 3 DRAM loads no matter what I try. I find that to be complete garbage. there are 3 other SBE on my trap team and they have NO problem shooting 3DRAM loads.

I am still open to suggestions.

[Nelli Girl]

Originally posted by kpiller:
Well, the verdict is mostly in on my jamming SBE. Replaced the locking pin, shot a 3DRAM load, still jammed, put a 3 3/4 DRAM in, cycled fine.

Apparently, my SBE WILL NOT shoot 3 DRAM loads no matter what I try. I find that to be complete garbage. there are 3 other SBE on my trap team and they have NO problem shooting 3DRAM loads.

I am still open to suggestions.

I suggest you call Customer Service.

[kpiller]

Do you work for Benelli?

Have you heard of this problem happening alot?

Originally posted by Nelli Girl:
</font><blockquote>quote:</font><hr />Originally posted by kpiller:
Well, the verdict is mostly in on my jamming SBE. Replaced the locking pin, shot a 3DRAM load, still jammed, put a 3 3/4 DRAM in, cycled fine.

Apparently, my SBE WILL NOT shoot 3 DRAM loads no matter what I try. I find that to be complete garbage. there are 3 other SBE on my trap team and they have NO problem shooting 3DRAM loads.

I am still open to suggestions.

I suggest you call Customer Service. </font>[/QUOTE]

[Rob Bartels]

I just got my SBE out of the box and ran a variety of loads through it. I started with 3-1/4 dram 1-1/8 oz of shot and it worked fine. I backed it down to 3 drams & then to 2-3/4 drams each with 1 oz of shot and it cycled everything. On the final shot with the 2-3/4 dram loads the bolt did not lock in the fully rearward position (though the action was partially open) however the first round cycled sufficiently to eject and then chamber the second. All of this with no break in period. I fired approximately 50 rounds through it.

Have you contacted Benelli yet? If so what have they said?

Take care