HK imported Benelli questions.

[Benelliman2]

Is there any refrence material out there that shows serial #'s and date cut offs for HK imported Benellis?? I have 12 HK import guns and would like to know a little about them. Also, are all shotgun recievrs and barrels serial numbered to match. I was cleaning my SBE (HK import) and noticed the serial on the frame has a U prefix and the "serial" number on the barrel had an S prefix. ANy help on this matter would help.
And I'm still confused about the whole 4th round in the carrier deal!!!

[Robert II]

Check out www.HKPro.com They have a fantastic reference section. You can also access the Forum board and ask questions. Best, Robert

[Benelliman2]

No help on the HKPRO site. Nothing in the refrence and/or forums sections.

[Robert II]

The Benelli is considered a "Long Gun" go to that board and click "search" then type in Benelli. You will get tons of information. Best, Robert

[tucker301]

Re: The fourth round in the carrier.
Not sure it will even work on the HK SBE, but I'll try to help explain.
_______________________________________
DISCLAIMER:
What YOU do to YOUR gun is YOUR responsibility.
I don't believe in lawyers... I believe in Benellis.
_______________________________________


On the bottom side of the bolt group, there is a small groove which is cut into the bottom of the carriage. it runs cross the assembly, NOT lengthways.

Filling this groove, until it is flush with the rest of the surrounding flat surface, with a strong epoxy like JB Weld will allow for a fourth shell to be loaded by the following means:
Load two rounds into the magazine.
Open the bolt and place one shell into the chamber. Keeping the bolt opened, place another shell onto the shell carrier. The carrier is the fork-shaped piece which lifts the shell from the magazine to the bolt during the autoloading sequence.
While holding the "floating" shell down, close the bolt, allowing the bolt to slide over the floated shell.
Make sure the bolt is fully closed.
When the weapon is fired, the second shell will be loaded into the chamber from the flaoted position, rather than from the magazine. Shells 3 and 4 will be loaded normally.

[ 06-27-2005, 08:45 AM: Message edited by: tucker301 ]

[Benelliman2]

That made things on the 4th round CRYSTAL clear!!!!!

THANKS!!!!!!!!!!!!

[jmikesteen]

Yep, that is the way I make my M3's hold 9 and my Franchi LAW-12 hold 10

[Benelliman2]

still no luck on the serial # front, anyone else???

[retrieverman]

I have 3 HK import Super 90's and the serial numbers on mine don't match either. I was told that since the barrels are interchangeable they carry their own serial number.

[jmikesteen]

This is from an old site that was up before the 94 ban ended, only thing I ever saw on benelli preban serial numbers.

Benelli (imported by H&K)
(703) 450-1900
I called H&K and they couldn't/wouldn't specify the "cutoff" serial number for pre/post ban Benelli's. Given this, the best we can do is post assorted serial numbers and import dates that will help you guess. If anyone comes up with a cutoff number, please let me know, and also please let me know any serial numbers and dates that you run by H&K.


Model Data
Benelli M1 Super 90 M1507xx, imported 12/01/92, pre-ban
M17142x, imported 1993, pre-ban
M1978xx, imported 08/94, pre-ban
M19833x, imported 09/19/94, post-ban*
M200050, imported 09/05/94, pre-ban*
M200100, imported 09/05/94, pre-ban*
M200111, imported 09/05/94, pre-ban*
M202200, imported 09/30/94, post-ban
M205200, imported 10/04/94, post-ban
M201xxx, imported 10/26/94, post-ban
M210025, imported 01/1995, post-ban
M215900, imported 03/1995, post-ban
Benelli M3 M19199x, imported 05/14/94, pre-ban
M1967xx, imported 08/94, pre-ban
M20595x, imported 11/04/94, post-ban

*Note: Discrepancy between M19833x (9/19/94 post-ban) and three larger serial numbers M200050, M200100, and M200111 (9/05/94 pre-ban). There is no accounting for this discrepancy. All information was provided by H&K and/or Benelli. Presumably the shipments of imports did not come in perfectly ordered by serial number. Many manufacturers and/or importers are in this same situation and that is why they can't provide a "cutoff" number.