Dave's Metal Works extension question

[rmcalhany]

Just got my DMW extension for my Benelli M2 Tactical. I have some questions I thought you guys would know the answer to.

The factory tube had a metal cap in the end, and no follower.
DMW's package has no cap at the end of the tube, and a red follower.

Is it right to just assemble the tube, follower and spring, without anything capping off the hole at the end? That seems odd to me.

If that is right, the next question, is which spring should I use? Does it matter?


Thanks.

Robert

[c rum]

Did you buy the tube kit new?
What length is the ext tube (how many extra does it add?)

It should have come with a spring and the end cap which looks like a follower (the end cap use to be black)

Depending on the number of rounds the ext tube adds you might be able to use the factory spring but as rule of thumb your spring should extend 12" -15" past the end of the ext tube (uncompressed)


Hope that helps

[rmcalhany]

Yes. New from Midway.
I can't post a link yet with my post count, but follow this route on Midway's site:
Homepage > Gun Parts > Universal Gun Parts > Shotgun Magazine Extension Tubes & Clamps >
It was the 3 round extension. Mag tube is now flush with my 18.5" barrel.

Ok, then the "end cap" is red and looks just like the nordic components follower I was using (a little smaller though). In fact, the Midway webpage, see link above, calls it a follower.

So, I take it that I'm not supposed to use my NC follower with this setup. That's a shame, I just bought it.

Odd that DMW uses the follower to seal the end of the tube.

I really hate the red end. Guess I'll have to have someone re-anodize it for me.

As for the spring, I'll have to measure things.

Thanks.

Robert

[rmcalhany]

Hey! Just noticed who responded to my post! My 2 trigger groups went to you in yesterday's mail.

Looking forward to seeing your handy work.

Robert

[Trapshooter1]

Yes. New from Midway.
I can't post a link yet with my post count, but follow this route on Midway's site:
Homepage > Gun Parts > Universal Gun Parts > Shotgun Magazine Extension Tubes & Clamps >
It was the 3 round extension. Mag tube is now flush with my 18.5" barrel.

Ok, then the "end cap" is red and looks just like the nordic components follower I was using (a little smaller though). In fact, the Midway webpage, see link above, calls it a follower.

So, I take it that I'm not supposed to use my NC follower with this setup. That's a shame, I just bought it.

Odd that DMW uses the follower to seal the end of the tube.

I really hate the red end. Guess I'll have to have someone re-anodize it for me.

As for the spring, I'll have to measure things.

Thanks.

Robert

Here is the link:
http://www.midwayusa.com/viewProduct...tNumber=180456

[rmcalhany]

That is the link, but doesn't show the follower. That's why I suggested clicking on the tubes & clamps link above that product. Then going to the DMW products (link on the left) to display all the DMW extension tubes. There you see the follower in the kits.

I'm guessing this really was intended to be a follower, and not a cap for the end of the tube. Although, I don't know how to cap the tube.

I've sent an email to DMW to get an explanation.

I'll also take some pics tonight and post them tomorrow.

Robert

[c rum]

My guess is the kit you received is missing the end cap.
The red follower is just that a follower.
If you don't hear back from DMW right away contact Midway and have them pull a kit and check it for an end cap. (should be black/blued steel)

Good luck (I will let you know when I receive you trigger groups)


Jeff