Search:

Yes, very nice. No more "dime store space gun look". I'm glad you liked the "un"-limiter. Thanks for posting the pix.
Joe

Thanks for taking the time and effort. I had calculated about the. My tubes are 8.5 oz, so a bit heavier, but not much, about the weight of one 12ga round.
I still have a few FL tubes ready for...

Before you install that beauty, any chance of getting an acurate weight. Would be good info to answer the question as to how much lighter the CC tube is as compared to my 4130 steel tube (8.5 oz). I...

Aluminum... I would be concerned that an AL tube with wall thickness sufficient to resist denting would not be that much lighter than the thin wall chrome-moly tube. Any small dent is likley to hang...

Thanks for asking , but I'll leave the TI stuff to CC, he aparently does very nice work with that material and has dedicated fans. I'm set up in my small shop to do the FL tubes in 4130 chrome-moly...

I just finished another small batch of M4 FL tubes, same "Socomguy" quality and price. Shipped the same or next day. For info ... [email protected]

I found your message, it came in as "junk mail" ... response sent

funkho... no message in my in box? try again
[email protected]

Carriercomp is, no doubt a high quality product, no bad mouthing here. I bit lighter, yes; I figure only about 3.6 oz. Thats based on my calculation of the weight of a TI tube vs my 4130 steel...

Yes, I still have a couple left.

I just finished four more FL tubes, all coated and ready to ship.... [email protected]

I have 5 more FL tubes out being coated, they will be ready to ship by Friday (3-22-13) . If you are interested... [email protected]

Joe

bhunted described it correctly, machined from solid 6061 aluminum. I'm happy that you like it! We always try to please!
Name , how about "slim-iter"

Joe

I just sent HIM one from my e-mail .. we will see ...

Joe

thazy2 , something is wrong! I don't see your e-mail. I'm up to date on all responses. Please try again, be sure of the address.... [email protected]

Joe

C, Thanks for the kind words, much appreciated. Like I said, there seems to be renewed interest out there! I have two tubes at the coater, will be ready next Tuesday and just finished making five...

bhunter, Ok now I think I understand. You want a screw on extension like the factory one except without the goofy necked down "space gun" look. Yes I can make one like that. Just realize that the...

bhunted... ref back to my 2-27-13 comment in this thread...
"The problem I see with a one piece 6 rd tube with a permanent (non removable) plug is that you could not load the follower and spring...

OOPS' , sorry I must have missed your e-mail, thought that I was up to date on communications. Here is where I'm at with FL tubes. The few that I had are all sold. I have two "in the white " that...

contact [email protected]

I'm still here, lurking.... I have not been active on the site since about a year ago when I announced that I was no longer going to make the FL tubes. At that time I sold off the few that I had on...

I believe that the issue would be "permanent and non- removable" to meet the requirements of the law. Just my guess

Joe B

John the NJ guy, The peoples Republic of NJ has a 6 round limit on the mag capacity. I while back, on special request I made a two piece 6 round tubw for a guy. I've attached a pic of the special...

Regulars on the forum may recall that after five years of making and selling quality steel mag tubes I said that I was stopping production, that was true I sold the last few that I had in stock back...

try searching "gunkote" or diamondkote" , find a gunsmith that does this work. Here in SE Michigan I have used M and R Arms for years with good results ... http://mrarms.com/

Joe B